Duckietown Appearance Specification

Tapes

There are 3 colors of tapes: white, yellow, and red.

White tape

Here are some facts about the white tapes:

• White tapes must be solid (not dashed)

• The width of the white tape is 1 inch.

• The white tape is always placed on the right hand side of a lane. We assume that the Duckiebots drive on the right hand side of the road.

• For curved roads, the white lane marker is formed by five pieces of white tape, while the inner corner is formed by three pieces, placed according to the specifications in the image below, where the edge pieces are matched to adjacent straight or curved tiles (Figure 2.2).

Yellow tape

On a two-way road, the yellow tape should be dashed. Each piece should have a length of approximately 2 in with a 1 in gap separating each piece.

Yellow tapes on curves: see curved road image in white tape section, pieces at tile edges should be in center of lane, piece at the middle of the curve should be approximately 20.5 cm from middle of inner center white piece of tape, with approximated circular arc in between.

Red tape

Red tapes MAY only appear on intersection tiles.

The red tape must be the full width of the duck tape roll and should cross the entire lane perpendicular to the lane.

The placement of red tape should always be under yellow and white tape.

A Duckiebot navigates Duckietown by a sequence of:

• Navigating one or more straight ties until a red tape appears,
• Wait for the coordination signal,
• Execute an intersection traversal,
• Relocalize in a StraightTile.

The guarantee is:

Topological Constraints During Map Construction

Here are some topological rule constraints that must be met:

1. An intersection can NOT be adjacent to a curved road tile or another intersection tile.

2. Any two adjacent non-empty tiles must have a feasible path from one to the other of length two: if they are adjacent, they must be connected.

Some examples of non-conforming topologies are shown in Figure 2.3.

Parking Lots

A parking lot is a place for Duckiebots to go when they are tired and need a rest.

A parking lot introduces three additional tile types:

1. Parking lot entry tile: This is similar to a straight tile except with a red stop in the middle. The parking lot sign (Figure 2.4o - parking) will be visible from this stop line.
2. Parking spot tiles:
3. Parking spot access tiles:

The following are the rules for a conforming parking lot:

1. One “parking spot” has size one tile.
2. From each parking spot, there is a path to go to the parking lot entry tile that does not intersect any other parking spot. (i.e. when a Duckiebot is parked, nobody will disturb it).
3. From any position in any parking spot, a Duckiebot can see at least two orthogonal lines or an sign with an April tag.

Launch Tiles

A “launch tile” is used to introduce a new Duckiebot into Duckietown in a controllable way. The launch file should be placed adjacent to a turn tile so that a Duckiebot may “merge” into Duckietow,n once the initialization procedure is complete.

A “yield” sign should be visible from the launch tile.

Specs

Center of signs are 13 cm height with apriltags of 6.5 cm sq. and a white border pasted below them.

Type

The allowable signs are as in Figure 2.4.

Each sign is printed from the signs and tags doc

Placement

Signs may appear on the opposite side and at the corner of the adjacent tile from which they are viewed. In the absence of any signs, it is assumed that all network flows are allowed so a sign MUST be placed and visible whenever this is not the case.

Signs must only be placed on empty tiles, or next to one of the other tile types if on the border of a map. The sign placements for four different cases are shown in Figure 2.5. At intersections, from each stop line 2 signs should be clearly visible: 1) the intersection type (traffic light or stop sign) and 2) the intersection topology.

At present, 4-way intersections must be equipped with traffic lights for safe navigation.

On straight and curved roads, additional signs can be added as desired. Their placement is indicated in Figure 2.5c - straight road and Figure 2.5d - curved road. The signs should be placed at the border between two tiles and should face towards oncoming traffic as indicated.

In these figures the arrow is the direction of the sign.

Specs

• Font: arial.

• Color: Perhaps we could start with real-world settings: white as foreground and green as background.

• Border: currently no additional borders

• The rounded corners are modified into 90 degrees.

• Height: sign board height is 1.5 in. (2.1 in),

• Width: Currently 4.5 in for id 500-511. (6.1 in +1.1 in “ST” or 5.5 in + 1.7 in “AVE”)

• Alphabet = English upper case. Different writing systems may need different algorithms.

• Text direction: Horizontal for alphabetical languages

Placement

• Similar to traffic light: The street name should sit on a pole that is based at the corner of the tile outside of the allowable driving region. The bottom of the street name should be at a height of 7in, and allow a duckiebot to pass through. The street names should be visible from both sides of the road.

Every segment of road must have at least one road name sign.

Every turn tile should have a road name sign.

The placement of the road name signs is as indicated in Figure 2.6.

Street name signs should never be perpendicular to the road - they are too big and obtrusive.

Specs

Placement

The lights must be at a height of exactly 20 cm above the center of the intersection tile.

The Raspberry Pi should sit on a pole that is based at the corner of the tile outside of the allowable driving region.